Product Showcase


Tuowen CNC, Craft Precision, Create Value.

PA Series Fully Automatic Loading Laser Tube Cutting Machine

Whole-Bundle Loading · Mixed-Type Auto-Recognition · Continuous Cutting, UnattendedThe PA Series takes the tube cutting platform of the PS Series and removes the operator from the loading cycle. whole-bundle loading system picks tubes directly from the storage rack, identifies the tube type automatic…

Product Category: Tube Metal Cutting Machine

Tel:+86-13012543158

brand: TW CNC

Product Details

PC Series Fully Automatic Tube Laser Cutting Machine | TWCNC
TWCNC · PC Series

PA Series Fully Automatic Tube Laser Cutting Machine

BOCHU EtherCAT Bus Control · Whole-Bundle Loading · Zero-Tail & Bevel Cutting Ready

The PA Series pairs TWCNC's fully automatic tube cutting platform with the BOCHU FSCUT5000 EtherCAT bus system — the control architecture built specifically for professional tube processing. Whole-bundle automatic loading runs in parallel with cutting, while TubesT 3D nesting and TubePro drive zero-tail cutting, bevel preparation and mixed-profile recognition from a single BOCHU software ecosystem. With optional servo-follow support and servo unloading, the PA Series is a tube production line controlled end-to-end by the system the tube industry already trusts.

1500–12000 W          Laser Power Range
BOCHU FSCUT5000          EtherCAT Bus System
Whole-Bundle          Automatic Loading
Zero-Tail          Material Saving Capable
Get PC Series Solution & Quote →

PA Series: Full Automation, Controlled by the Tube Industry's Native Bus System

The PA Series starts from the same premise as the PA Series — remove the operator from the loading cycle and keep the laser cutting — but executes it on the BOCHU FSCUT5000 EtherCAT bus platform. This is not a general-purpose CNC adapted for tube; FSCUT5000 was designed from the ground up for fiber laser tube            cutting, with dedicated hardware modules and a tube-native software chain. The result is tighter synchronization between the loader, the chucks, the follow-up support and the cutting head than retrofitted control architecture can deliver.

The PA Series is configured around BOCHU's TubesT 3D nesting + TubePro cutting software. TubesT handles part layout, common-edge nesting and full-profile compensation; TubePro executes the toolpath with real-time process control[reference:1]. Together they enable zero-tail cutting — the system cuts the final part close to the chuck without leaving a discarded stub — and bevel cutting driven directly by the nesting drawing. For fabricators already familiar with BOCHU tube systems, the PA Series eliminates the learning curve entirely.

BOCHU FSCUT5000 EtherCAT Bus TubesT + TubePro Software Chain Whole-Bundle Automatic Loading Zero-Tail Cutting Bevel Cutting Ready
PC Series Fully Automatic Tube Laser Cutting Machine with BOCHU Bus System

Tube Line Built on the BOCHU Bus Foundation

The PA Series differentiates on control integration: every subsystem — loading, chuck motion, support, nesting and cutting — speaks the same bus language.

🔗

BOCHU FSCUT5000 EtherCAT Bus

Dedicated tube-cutting bus system with CypTronic-Pro bus master, BCS100E height control and wireless handwheel. FSCUT5000B for standard dual-chuck configurations; FSCUT5000A for three-chuck / heavy-tube configurations. The bus architecture keeps motion, I/O and process control synchronized across the entire line.[reference:4]

🧩

TubesT 3D Nesting + TubePro

TubesT generates optimized nesting with common-edge cutting and full-profile compensation; TubePro executes the cut with a tube-native interface and a large display. From drawing to finished part, the software chain is BOCHU end-to-end — no third-party translation layer.[reference:6]

✂️

Zero-Tail Cutting

BOCHU's zero-tail cutting function reduces the discarded stub at the end of each tube, improving material yield per bundle. Combined with TubesT common-edge nesting, the PC Series targets material savings that show up directly in the cost per part.

📐

Bevel Cutting Optional

FSCUT5000 supports bevel cutting directly from nesting drawings. V-, Y-, K- and X-type weld preparations are produced in the same setup as the cut-off, eliminating secondary chamfering and improving joint fit for welding-intensive tube assemblies.

📏

Servo-Follow Support Optional

Servo-driven support rollers track the tube's rotation and adjust height in real time. This suppresses sag on long tubes and tail-end whip on spinning profiles, keeping the cut stable even as the remaining tube length shrinks — a critical requirement for automatic unloading consistency.

📤

Servo Unloading Table Optional

A servo-controlled receiving table lowers cut parts in a controlled motion. Edge damage, noise and scattered parts are eliminated — the part lands where the automation expects it, ready for the next step rather than for manual collection.

PA Series Technical Specifications

The following specifications are indicative for standard PA Series fully automatic tube cutting configurations with BOCHU bus control. Chuck configuration, tube range and optional modules are specified per project.

ParameterPA Series (Indicative Range)
Machine TypeFully Automatic Tube Laser Cutting Machine
Control SystemBOCHU FSCUT5000 EtherCAT Bus System (FSCUT5000B dual-chuck / FSCUT5000A three-chuck configuration)
Nesting / Cutting SoftwareBOCHU TubesT 3D Nesting + TubePro
Laser Power Range1500 W / 2000 W / 3000 W / 6000 W / 12000 W
Standard Cutting Length6200 mm (longer options available)
Tube Diameter / Section RangeRound Φ20 – Φ220 mm · Square / rectangular / special profiles within equivalent envelope
Loading MethodWhole-bundle automatic loading · loading synchronized with cutting
Chuck ConfigurationDual pneumatic chuck standard · three-chuck / heavy-tube configuration available with FSCUT5000A
Support SystemServo-follow support (optional / configuration-dependent)
UnloadingSemi-automatic standard · Servo unloading table optional
Bevel CuttingOptional ±45° (V / Y / K / X weld preparation, driven from nesting drawing)
Positioning Accuracy±0.03 mm/m
Repositioning Accuracy±0.03 mm
Max. Acceleration1.0 – 1.2 G
Max. Linkage Speed100 m/min
Laser Source / HeadRaycus / IPG · Raytools / BOCI (configuration-dependent)
Applicable MaterialsRound tube, square tube, rectangular tube, oval tube, angle, channel, special profiles
Power SupplyAC 380 V / 50–60 Hz / Three-phase

* Specifications above are indicative and based on typical fully automatic tube cutting configurations in the PA Series class with BOCHU bus control. Chuck configuration, tube range and optional module scope vary by project.FSCUT5000A is required for three-chuck / heavy-tube configurations; FSCUT5000B applies to standard dual-chuck configurations. Servo unloading table, servo-follow support and ±45° bevel cutting are optional and must be specified at order. Please contact TWCNC for the confirmed specification sheet and a production cycle assessment based on your tube mix and bundle loading requirements.

For Tube Fabricators Standardizing on the BOCHU Ecosystem

The PA Series suits operations that already run BOCHU tube systems, or that want a fully automatic line with control and software chain the tube industry has standardized on.

Metal Furniture Mass Production        Fitness Equipment Frames        Automotive Tube Components        Steel Structure & Truss        Scaffolding & Racking        Bicycle & E-Bike Frames        HVAC & Ventilation        Handrails & Guardrails        Machinery Tube Parts        High-Volume Tube Job Shops        Welding-Intensive Fabrication        Shops Standardized on BOCHU Control

Specify Your PC Series BOCHU Tube Line

Tell us your tube mix, maximum length, wall thickness, bundle weight and whether you need three-chuck heavy-tube        capability, bevel cutting or servo unloading. The TWCNC application team will confirm the FSCUT5000 variant,        tube range and optional modules, and provide a production cycle estimate for your bundle loading requirements.

       Contact TWCNC for a Solution →      

BOCHU FSCUT5000 Bus Control · TubesT + TubePro · Whole-Bundle Automatic Loading · Zero-Tail & Bevel Ready

Related Products