Uncoiling · Leveling · Cutting · Blanking — Continuous Production Directly from Steel Coil
The YD Series is TWCNC's coil-fed laser cutting and blanking line, designed to process steel coil directly into finished flat blanks without intermediate shearing or separate leveling operations. From loading, uncoiling and leveling through laser cutting and unloading, the entire flow runs automatically — eliminating coil waste, reducing manual handling and turning raw coil stock into production-ready parts in one continuous pass.
Conventional sheet laser cutting starts with pre-cut flat plates: coil must first be uncoiled, sheared and leveled by separate equipment, then transported to the laser. The YD Series removes those intermediate steps. It loads steel coil up to 20 tonnes — roughly six times the capacity of ordinary feeding equipment — uncoils the strip, passes it through precision leveler that eliminates coil-set and internal stress, and feeds the flattened strip directly into the laser cutting zone. The cut blanks are then unloaded automatically, completing the coil-to-part flow in a single line[reference:0]. Because the strip is leveled immediately before cutting, the sheet lies flatter and the cutting process is more stable. The line also breaks through the length limitation of conventional laser cutting: production is no longer constrained by fixed table size, since the material is fed continuously. This makes the YD Series particularly valuable where long parts, high-volume blanks or uninterrupted coil consumption define the production model[reference:1]. The YD Series is not a laser cutter with a feeder attached. It is a coil processing line in which laser cutting is one integrated station — and every design decision reflects that. The loading system handles coils up to 20 tonnes, breaking through the 3-tonne feeding limit of ordinary equipment. Fewer coil changes mean longer uninterrupted production runs[reference:2]. The precision leveler flattens the uncoiled strip and eliminates internal stress before cutting. Flatter material produces more stable cutting, better edge quality and fewer scrap events[reference:3]. Loading → uncoiling → leveling → laser cutting → unloading runs as one automated sequence. A process that previously required multiple operators can be run by a single person, reducing labor and handling damage[reference:4]. Because material is fed continuously rather than positioned on a fixed table, the YD Series is not limited by conventional laser cutting length. Long blanks and continuous nesting become practical production options[reference:5]. The ultra-precision transmission system holds sheet feeding accuracy to approximately ±0.5 mm, ensuring that the cut position remains consistent relative to the leveled strip throughout the run[reference:6]. Direct coil processing targets zero coil waste and removes the separate shearing/leveling step. Combined with single-operator automation, the line reduces both material loss and per-part labor cost[reference:7]. The following specifications are indicative for standard YD Series steel coil laser cutting configurations.Working area, coil capacity and line layout can be customized based on coil dimensions and blank requirements. * Specifications above are based on standard TWCNC YD Series steel coil laser cutting configurations. Working area, coil weight capacity, leveling specifications and line layout are customizable. Actual line footprint and weight depend on the selected coil car, leveler and unloading configuration. Please contact TWCNC for the confirmed specification sheet and line layout drawing for your coil dimensions and blank requirements. The YD Series suits manufacturers whose production is built around steel coil rather than pre-cut sheets — especially where blank volumes are high and material handling is a bottleneck. Tell us your coil width, coil weight, strip thickness, required blank sizes and target output per shift. The TWCNC application team will recommend the appropriate YD Series working area, leveling setup and line layout, and support you with blank samples or line throughput calculations. 24-Month Warranty · Installation & Training · 7×24 Remote DiagnosisYD Series: From Coil to Blank, One Continuous Line

Built for Coil-Based Production, Not Just Cutting
20 T Heavy-Duty Coil Loading
In-Line Leveling & Stress Relief
Fully Automatic Coil-to-Blank Flow
Unconstrained Cutting Length
High-Precision Strip Transmission
Material Utilization & Labor Savings
YD Series Technical Specifications
Parameter YD Series Machine Type Steel Coil Laser Cutting Machine (Uncoiling–Leveling–Cutting–Blanking Line) Working Area Options 3000 × 1500 mm / 4000 × 2000 mm / 6000 × 2000 mm / 6000 × 2500 mm / Custom Coil Loading Weight Up to 20 T Table Load Bearing 2500 kg Leveling In-line precision leveling with stress relief Feeding Accuracy Approx. ±0.5 mm Positioning Accuracy ±0.03 mm Repositioning Accuracy ±0.02 mm Max. Linkage Speed 80 m/min Max. Acceleration 1 G Laser Head Raytools Laser Source Raycus / IPG / Max (configurable) X / Y / Z Axis Drive Servo motor and driver (Yaskawa / Japan Fuji) Control System FSCUT2000 / FSCUT8000 / Other Display 28" Machine Bed Structure Section bar welding · Gantry structure · Cast aluminum Overall Dimensions 11850 × 3470 × 2280 mm Overall Weight ≥ 7210 kg Where Coil-to-Blank Efficiency Changes the Production Model
Discuss Your YD Series Coil Line Configuration